基于系统性能的近地告警技术研究

基于多种导航信息综合处理、告警计算的近地告警系统，对于避免可控撞地事故、 提升飞机安全具有重要意义。本文首先介绍了近地告警系统的工作原理，研究了基于 SOC 曲线的告警包线设计技术，并以过大近地速率告警模式为例进行了告警包线的仿真。最后，利用实际飞行数据分析验证了告警包线合理性以及导航信息可靠性对系统性能的影响。     

响应面法优化艾叶挥发油的提取工艺及其抗氧化性能研究

以艾叶挥发油提取率为考核指标,采用单因素实验考察浸泡时间、料液比、提取时间等对艾叶挥发油提取率的影响,在此基础上,采用响应面法优化艾叶挥发油的共水蒸馏提取工艺,并通过紫外分光光度法测定艾叶挥发油对DPPH自由基的清除率来评价其抗氧化性能。结果表明,艾叶挥发油的最佳提取工艺条件为:浸泡时间1.5 h、料液比1∶10(g∶mL)、提取时间4.5 h,在此条件下,艾叶挥发油提取率最高,为0.83%。当艾叶挥发油浓度为80 mg·mL~(-1)时,DPPH自由基清除率最高,为39.12%。表明艾叶挥发油具有一定的抗氧化活性。     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

Porous sunflower plate-like NiFe2O4/CoNi–S heterostructure as efficient electrocatalyst for overall water splitting

Constructing high-efficient and nonprecious electrocatalysts is of primary importance for improving the efficiency of water splitting. Herein, a novel sunflower plate-like NiFe₂O₄/CoNi–S nanosheet heterostructure was fabricated via facile hydrothermal and electrodeposition methods. The as-fabricated NiFe₂O₄/CoNi–S heterostructure array exhibits remarkable bifunctional catalytic activity and stability toward oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in alkaline media. It presents a small overpotential of 219 mV and 149 mV for OER and HER, respectively, to produce a current density of 10 mA cm^?2. More significantly, when the obtained electrodes are used as both the cathode and anode in an electrolyzer, a voltage of 1.57 V is gained at 10 mA cm^?2, with superior stability for 72 h. Such outstanding properties are ascribed to: the 3D porous network structure, which exposes more active sites and accelerates mass transfer and gas bubble emission; the high conductivity of CoNi–S, which provides faster charge transport and thus promotes the electrocatalytic reaction of the composites; and the effective interface engineering between NiFe₂O₄ (excellent performance for OER) and CoNi–S (high activity for HER), which leads to a shorter transport pathway and thus expedites electron transfer. This work provides a new strategy for designing efficient and inexpensive electrocatalysts for water splitting.     

铸态Ti-20Zr-20Al钛合金动态压缩力学性能与断裂机制研究

采用X射线衍射仪、金相显微镜、分离式霍普金森杆和扫描电镜等手段研究了Ti-20Zr-20Al钛合金在动态压缩条件下的微观结构、力学性能和断裂机制。结果表明,Ti-20Zr-20Al铸态合金由Zr基体相和TiAl/Ti₃Al针状相组成; 随着应变率增加,合金的抗压强度增加,失效应变显著增加; Ti-20Zr-20Al合金的断裂机制为解理断裂; 随着应变率增加,试验压缩断裂后碎片总数增大,平均粒径减小。采用DID模型模拟的材料碎片尺度与实验结果比较吻合,Grady模型与实验结果的偏差较大。     

基于旋翼负压混合吸附的爬壁清洗机器人系统动力学性能研究

针对爬壁清洗机器人越障时,负压装置的吸附力下降导致吸附不稳定的问题,设计了一种旋翼负压混合吸附工作的多边形履带清洗机器人,并对爬行稳定性及越障性能进行了动力学分析。首先根据机器人爬壁的运动原理,建立机器人沿玻璃幕墙上的动力学模型,计算出电机理论驱动力矩;其次分析机器人在跨越障碍过程中的运动模型,结合与壁面接触的实际受力状态,对越障过程中关键阶段的本体倾翻、滑移两种失效形式进行运动学和动力学分析;然后根据玻璃幕墙实际的障碍高度,确定多边形履带的参数和理论驱动力矩的大小,并研制了实验样机进行爬行和越障试验,结果表明所设计的机器人具有良好的越障性能。     

Hydrogel photocatalysts for efficient energy conversion and environmental treatment

Photocatalysts have attracted great research interest owing to their excellent properties and potential for simultaneously addressing challenges related to energy needs and environmental pollution. Photocatalytic particles need to be in contact with their respective media to exhibit efficient photocatalytic performances. However, it is difficult to separate nanometer-sized photocatalytic materials from reaction media later, which may lead to secondary pollution and a poor recycling performance. Hydrogel photocatalysts with a three-dimensional (3D) network structures are promising support materials for photocatalysts based on features such as high specific surface areas and adsorption capacities and good environmental compatibility. In this review, hydrogel photocatalysts are classified into two different categories depending on their elemental composition and recent progresses in the methods for preparing hydrogel photocatalysts are summarized. Moreover, current applications of hydrogel photocatalysts in energy conversion and environmental remediation are reviewed. Furthermore, a comprehensive outlook and highlight future challenges in the development of hydrogel photocatalysts are presented.     

综合高速效应的凝析气藏流入动态

当井底压力低于露点压力时,凝析液在近井地带开始析出并不断聚集产生凝析油堵塞现象。因此,在制定凝析气井工作制度时,通常以控制生产压差为指导思想,往往忽略高速流动下凝析气液相变的非平衡特征。对于凝析气体系,当外界温压变化速度超过凝析气液的相平衡速度时,凝析气体系相变滞后,开始呈现非平衡特征,即凝析液的析出量随着压降速度的增加而减小。凝析气在向井筒流动的过程中,近井区高速流动使凝析气产生非平衡相变,凝析气在比较高的压降速度下流入井筒,使得凝析液来不及析出。在分析非平衡相变规律与近井地带凝析气渗流参数分布的基础上,评价凝析气液流动过程中的非平衡特征,给出了考虑非平衡相变的凝析液饱和度分布计算公式,并进行了产能预测结果对比。实例分析表明,可以通过适当放大生产压差,增加凝析气液相变非平衡特征,减小井筒附近的凝析液饱和度,提高气井产能与气藏开发效果。     

球罐自动焊应用现状及其焊缝跟踪技术研究

球罐制造是以焊接为主要加工手段的一个复杂的系统工程,涉及到多门学科理论和技术领域。基于球罐制造过程的特殊性,综述了球罐自动化焊接技术的发展概况和应用现状,从工程应用发展角度出发,分析了球罐自动焊接过程中焊缝跟踪技术的研究进展和应用前景。